国产精品国产三级在线专区,亚洲午夜国内自产拍在线观看,在线观看国产视频一区,善良的嫂子中文字幕在线

歡迎進入濟南濟柴環能燃氣發電設備有限公司官網!
當前位置:首頁 - 新聞中心 - 公司新聞

公司新聞

沼氣發電機組如何處理轉速不穩定?

返回 2020.05.04 來源:http://www.pp198.cn 0
  沼氣發電機組如何處理轉速不穩定?
  How to deal with the unstable speed of biogas generator set?
  一、無法開始
  1、 Can't start
  1.無速度反饋信號:檢查速度傳感器和電纜。
  1. No speed feedback signal: check speed sensor and cable.
  2.調速器電源斷開或反向連接:檢查電源和線路。
  2. Governor power disconnection or reverse connection: check power supply and circuit.
  3.節流堵塞:重新安裝和調試。
  3. Throttling blockage: reinstallation and commissioning.
沼氣發電機組
  4.啟動油量設定值過低:適當增加啟動油量。
  4. The setting value of starting oil is too low: increase the starting oil properly.
  5.速度設置過低:順時針旋轉低速電位器,增加空轉速度。
  5. Speed setting too low: turn the low-speed potentiometer clockwise to increase the idle speed.
  二、開始加速
  2、 Start to accelerate
  1.執行機構和節氣門機構減少氣體方向或零位置不匹配:檢查和重新安裝調整。
  1. Actuator and throttle mechanism reduce gas direction or zero position mismatch: check and reinstall.
  2.速度控制系統速度設定過高:將低速設定值調整到校準設定值。
  2. Speed setting of speed control system is too high: adjust the low speed setting value to the calibration setting value.
  3.調速器電流限制過高:適當減少起動油量。
  3. Governor current limit is too high: reduce starting oil properly.
  4.控制器參數調整不當:適當增加控制器的“增益”和“差動”。
  4. Improper adjustment of controller parameters: properly increase the "gain" and "differential" of the controller.
  三、速度不穩定
  3、 Speed instability
  1.傳動桿系統卡死或執行機構與節流閥間隙:檢查并重新安裝調整。
  1. The transmission rod system is stuck or the clearance between the actuator and the throttle valve is checked and reinstalled for adjustment.
  2.發動機過載:減少發動機負荷。
  2. Engine overload: reduce engine load.
  3.速度傳感器安裝間隙過大:檢查并重新安裝和調整。
  3. The installation clearance of speed sensor is too large: check, reinstall and adjust.
  4.控制器參數調整不當:調整增益、差動和狀態開關。
  4. Improper adjustment of controller parameters: adjust gain, differential and status switches.
  5.如果屏蔽線連接不正確,電磁干擾會造成不穩定:檢查屏蔽線連接是否正確。
  5. If the shield wire is not connected correctly, electromagnetic interference will cause instability: check whether the shield wire is connected correctly.
  以上方案不限于沼氣發電機組、天然氣發電機組、燃氣發電機組、生物質燃氣發電機組、燃氣發電機組等,也可執行上述操作。
  The above scheme is not limited to biogas generator set, natural gas generator set, gas generator set, biomass gas generator set, gas generator set, etc., but also can perform the above operations.
新聞搜索
濟南濟柴環能燃氣發電設備有限公司
  • 服務熱線

    0531-62325028
    0531-69951266

沼氣發電機組如何處理轉速不穩定?

  沼氣發電機組如何處理轉速不穩定?
  How to deal with the unstable speed of biogas generator set?
  一、無法開始
  1、 Can't start
  1.無速度反饋信號:檢查速度傳感器和電纜。
  1. No speed feedback signal: check speed sensor and cable.
  2.調速器電源斷開或反向連接:檢查電源和線路。
  2. Governor power disconnection or reverse connection: check power supply and circuit.
  3.節流堵塞:重新安裝和調試。
  3. Throttling blockage: reinstallation and commissioning.
沼氣發電機組
  4.啟動油量設定值過低:適當增加啟動油量。
  4. The setting value of starting oil is too low: increase the starting oil properly.
  5.速度設置過低:順時針旋轉低速電位器,增加空轉速度。
  5. Speed setting too low: turn the low-speed potentiometer clockwise to increase the idle speed.
  二、開始加速
  2、 Start to accelerate
  1.執行機構和節氣門機構減少氣體方向或零位置不匹配:檢查和重新安裝調整。
  1. Actuator and throttle mechanism reduce gas direction or zero position mismatch: check and reinstall.
  2.速度控制系統速度設定過高:將低速設定值調整到校準設定值。
  2. Speed setting of speed control system is too high: adjust the low speed setting value to the calibration setting value.
  3.調速器電流限制過高:適當減少起動油量。
  3. Governor current limit is too high: reduce starting oil properly.
  4.控制器參數調整不當:適當增加控制器的“增益”和“差動”。
  4. Improper adjustment of controller parameters: properly increase the "gain" and "differential" of the controller.
  三、速度不穩定
  3、 Speed instability
  1.傳動桿系統卡死或執行機構與節流閥間隙:檢查并重新安裝調整。
  1. The transmission rod system is stuck or the clearance between the actuator and the throttle valve is checked and reinstalled for adjustment.
  2.發動機過載:減少發動機負荷。
  2. Engine overload: reduce engine load.
  3.速度傳感器安裝間隙過大:檢查并重新安裝和調整。
  3. The installation clearance of speed sensor is too large: check, reinstall and adjust.
  4.控制器參數調整不當:調整增益、差動和狀態開關。
  4. Improper adjustment of controller parameters: adjust gain, differential and status switches.
  5.如果屏蔽線連接不正確,電磁干擾會造成不穩定:檢查屏蔽線連接是否正確。
  5. If the shield wire is not connected correctly, electromagnetic interference will cause instability: check whether the shield wire is connected correctly.
  以上方案不限于沼氣發電機組、天然氣發電機組、燃氣發電機組、生物質燃氣發電機組、燃氣發電機組等,也可執行上述操作。
  The above scheme is not limited to biogas generator set, natural gas generator set, gas generator set, biomass gas generator set, gas generator set, etc., but also can perform the above operations.
买车| 杭锦旗| 上思县| 临澧县| 沂源县| 惠水县| 五家渠市| 广水市| 永顺县| 永定县| 黄骅市| 建瓯市| 曲松县| 榆社县| 东阳市| 桓台县| 方山县| 东平县| 彭阳县| 凤冈县| 沙湾县| 泌阳县| 伊吾县| 霸州市| 庄浪县| 广昌县| 青神县| 河曲县| 马鞍山市| 安乡县| 马尔康县| 盐山县| 利辛县| 确山县| 衡水市| 涿州市| 礼泉县| 潢川县| 德兴市| 城步| 康定县|