在線咨詢
官方二維碼
當前位置：
2022.11.30
燃?xì)獍l(fā)電機多個部位沒問題后的故障檢查
在確定多個部位沒有故障，判定故障可能發生在燃?xì)庋b置上。故障排除方法是怎樣的？下面燃?xì)獍l(fā)電機組廠家為您講解。
It is determined that there is no fault in several parts, and the fault may occur in the gas device. What is the troubleshooting method? The manufacturer of gas generator set will explain it to you.
1)燃?xì)鈩?dòng)力閥間隙太小，燃?xì)饬髁坎粔?，混合氣過稀。調整動力閥，國Ⅲ系列燃?xì)獍l(fā)電機組的動力閥裝在減壓器出氣口，動力閥有刻度，R(-)方向?yàn)闇p小，L(+)方向?yàn)樵龃蟆?/div>
1) The clearance of the gas power valve is too small, the gas flow is not enough, and the mixture is too thin. Adjust the power valve. The power valve of the national III series gas generator set is installed at the outlet of the pressure reducer. The power valve has a scale. The R (-) direction decreases, and the L (+) direction increases.
2)檢查燃?xì)膺^濾器有無堵塞。
2) Check the fuel gas filter for blockage.
3)檢查壓力平衡管是否漏氣或破損。
3) Check whether the pressure balance pipe leaks or is damaged.
4)增壓中冷系統是否有漏氣，檢查排氣管墊、增壓器接口、中冷器、混合器、進氣管及各連接硅膠管，增壓器有無損害。
4) Check the exhaust pipe gasket, turbocharger interface, intercooler, mixer, intake pipe and all connecting silicone hoses of the supercharger for damage.
5)排氣管道或三元催化器堵塞，致排氣阻力增大。
5) The exhaust pipe or three-way catalyst is blocked, resulting in increased exhaust resistance.
6)檢查空氣濾清器是否良好，進氣管路是否暢通。
6) Check whether the air filter is in good condition and whether the air inlet pipe is unblocked.
7)檢查燃?xì)獠竭M(jìn)電機及減壓器出氣口到混合器之間的管路。
7) Check the pipeline from the gas stepping motor and pressure reducer outlet to the mixer.
8)混合器皮膜破損，不能形成合理的空燃比，更換皮膜。
8) The skin film of the mixer is damaged and cannot form a reasonable air fuel ratio. Replace the skin film.
9)中低壓減壓閥二級閥片行程過小。
9) The stroke of the secondary valve plate of the medium and low pressure reducing valve is too small.
10)減壓器電磁閥閥芯、閥孔是否破損，進氣量不夠，更換電磁閥。
10) If the solenoid valve core and valve hole of the pressure reducer are damaged and the air intake is insufficient, replace the solenoid valve.
11)檢查低減壓器的膜片、彈簧、桿桿有無損害。
11) Check whether the diaphragm, spring and rod of the low pressure reducer are damaged.
排查一下燃?xì)獍l(fā)電機組的工作情況，看看故障的存在情況明不明顯，檢查過后記得進行清潔。更多相關內容就來我們網站http://www.pp198.cn進行咨詢！
Check the working condition of the gas generator set to see if the fault is obvious, and remember to clean it after inspection. More relevant content will come to our website http://www.pp198.cn Consult!