瓦斯發電機是采用機械內混方式，定時地打開燃?xì)忾y將可燃?xì)怏w噴入氣缸，使燃?xì)馀c空氣在缸內混合，進行燃燒。那你知道怎么對瓦斯發電機提高安裝效率嗎？下面瓦斯發電機組廠家為您進行解答。

The gas generator adopts the mechanical internal mixing mode. Open the gas valve regularly to inject combustible gas into the cylinder, so that the gas and air can be mixed in the cylinder for combustion. Do you know how to improve the installation efficiency of gas generator? The manufacturer of gas generator set will answer for you.

這樣通過增壓器、進氣管的氣體始終是不可燃的純空氣，避免了回火問題。但是，由于爆燃現象時有發生，機組的活塞、氣缸、進排氣門、進排氣門座等故障頻繁，使用壽命降低，維護量相當大。

In this way, the gas passing through the supercharger and intake pipe is always non combustible pure air, avoiding the problem of backfire. However, due to the frequent occurrence of deflagration, the piston, cylinder, intake and exhaust valves, intake and exhaust valve seats and other faults of the unit are frequent, the service life is reduced, and the amount of maintenance is considerable.

為了安裝的方便、快捷，利用報廢的缸套加工了一個錐套(錐套的內外徑基本按照缸套的原有尺寸不變，僅僅在頂部加工一段錐面，并在錐面與內孔交界處倒一個大圓角，方便活塞環能順利壓入錐套。

In order to install conveniently and quickly, a taper sleeve is processed using the scrapped cylinder liner (the inner and outer diameters of the taper sleeve are basically the same as the original dimensions of the cylinder liner, only a section of taper surface is processed at the top, and a large fillet is poured at the junction of the taper surface and the inner hole, so that the piston ring can be pressed into the taper sleeve smoothly.

在把活塞安裝到氣缸之前就把錐套套在活塞環處，使全部活塞環都處于正常使用時的壓縮狀態，安裝時僅僅需要先把活塞裙部放在氣缸內，然后稍作調整，使氣缸與錐套同心，再輕輕用手緩緩地將活塞推入到氣缸內。這樣不但降低了勞動強度，而且提高了安裝效率。

Before installing the piston to the cylinder, put the taper sleeve on the piston ring, so that all piston rings are in the compression state in normal use. During installation, just put the piston skirt in the cylinder, and then make a slight adjustment to make the cylinder and taper sleeve concentric, and then gently push the piston into the cylinder with your hands. This not only reduces the labor intensity, but also improves the installation efficiency.

此外通過相關規定的保養，能及時發現機組是否存在聲音異常、動作異常、外觀異常、溫度異常、壓力異常和氣味異常等故障現象，從而及時對機組進行檢查和調整，進而有針對性的加以解決，更多有關內容就我們網站http://www.pp198.cn進行咨詢了解吧！

In addition, through the maintenance of relevant regulations, it can timely find out whether the unit has abnormal sound, action, appearance, temperature, pressure, smell and other faults, so as to timely check and adjust the unit, and then targeted solutions. For more information, please refer to our website http://www.pp198.cn Consult and understand!