The function of the air filter in the gas generator set is to filter the dust in the air of the cylinder to ensure that the engine has enough clean air mixed with the fuel to produce combustion. The engine needs 14kg / air for every 1kg / diesel. If the dust in the air is not filtered, the wear of the cylinder, piston and piston ring will be greatly increased. The requirements of the air filter are: strong filtration capacity, small resistance to air, simple structure, convenient use and maintenance.

只有定期的保養，才能延長燃?xì)獍l(fā)電機組的使用壽命。下面我們就來看一下燃?xì)獍l(fā)電機組的空濾器保養方法。發動機在裝有空濾器的情況下使用，如空濾器指示器報警，應清潔或更換空濾器濾芯。

Only regular maintenance can prolong the service life of gas generator set. Now let's take a look at the maintenance method of air filter of gas generator set. When the engine is used with an air filter, if the air filter indicator gives an alarm, clean or replace the air filter element.

1、檢查傳動膠帶：檢查膠帶是否有裂紋，如出現縱向和橫向貫穿的裂紋，膠帶磨損或材料剝落等現象，應更換膠帶。在膠帶的大跨距處測量其撓度。大撓度不應大于13mm。如有膠帶張緊力測量?jī)x，可在膠帶大跨距處測量其張力，張力極限為360～490N。

1. Check the drive belt: check whether there are cracks on the belt. If there are longitudinal and transverse cracks, belt wear or material peeling, replace the belt. Measure the deflection of the tape at the large span. Large deflection should not be more than 13mm. If there is a belt tension measuring instrument, the tension can be measured at the large span of the belt, and the tension limit is 360 ~ 490N.

燃?xì)獍l(fā)電機組廠家圖

Manufacturer's drawing of gas generator set

2、定期清洗濾清器，清除積塵蓋上的塵土，細心地刷去紙質芯清上的塵土，也可以用打氣筒從濾芯孔向外吹出塵土，防止紙質濾芯損壞，如破損則應更換。

2. Clean the filter regularly, remove the dust on the dust cover, and carefully brush the dust on the paper core. You can also use the air pump to blow out the dust from the center hole of the filter element to prevent the paper filter element from being damaged. If it is damaged, replace it.

3、更換冷卻液濾清器：車輛停止運行后，務必等冷卻液溫度低于50C后，方可拆下散熱器加水蓋。在更換冷卻液濾清器前，先關閉進出水截流閥，以防止熱的冷卻液噴霧傷人！拆下冷卻液濾清器并清潔濾清座密封平面。先在濾清器密封橡膠墊圈表面涂一層薄機油，再安裝冷卻液濾清器，擰緊力矩24±2N.m。

3. Replace the coolant filter: after the vehicle stops running, be sure to wait until the coolant temperature is lower than 50c before removing the radiator water cap. Before changing the coolant filter, close the inlet and outlet valve to prevent the spray from injure. Remove the coolant filter and clean the sealing surface of the filter base. Apply a thin layer of engine oil on the surface of the sealing rubber gasket of the filter, and then install the coolant filter. The tightening torque is 24 & plusmn; 2N.m。

4、安裝完后，務必打開燃?xì)獍l(fā)電機組冷卻液濾清器進出水截流閥，再裝上散熱器加水蓋。

4. After installation, be sure to open the inlet and outlet shut-off valve of the coolant filter of the gas generator set, and then install the radiator water cap.