According to the principle of fault analysis and troubleshooting to find the fault of gas generator set, improve the accuracy of fault discovery

　　當發生故障時，要注意從故障現象分析故障原因，根據原理分析結構。當故障發生時，首先要考慮以下三個問題:(1)故障發生前發生了什么?(2)故障發生前，您做了哪些維護和維修工作?(3)你以前遇到過類似的情況嗎?你是怎么處理的?此外，如果允許機組在運行過程中確定問題，則可以在運行過程中確定問題。

　　In case of failure, it is necessary to analyze the cause of failure from the failure phenomenon and analyze the structure according to the principle. When a fault occurs, the following three problems should be considered first: (1) what happened before the fault occurs? (2) what maintenance and repair work did you do before the fault occurs? (3) have you encountered similar situations before? How did you deal with them? In addition, if the unit is allowed to determine the problem during operation, the problem can be determined during operation.

　　單元操作,例如,如果發現排氣溫度過高或突然一個氣缸排氣溫度變化大,應首先在設備運行條件下檢查各缸氣體調節器松散,排除氣體調節器不松的問題仍然存在,應停止檢查點火系統,如:火花塞和點火線圈等是否有問題;如果出現排氣溫度異常，應區分是單缸還是全缸。如果是單缸異常，應考慮儀表顯示是否異常，可通過測量熱電動勢或?qū)Ь€倒置消除。如果這是一種全球異常，考慮是否有氣體濃度的變化或點火不良。

　　Unit operation, for example, if it is found that the exhaust temperature is too high or suddenly the exhaust temperature of a cylinder changes greatly, the gas regulator of each cylinder shall be checked for looseness under the operation condition of the equipment first, and the problem that the gas regulator is not loose shall be eliminated. The ignition system, such as spark plug and ignition coil, shall be checked for any problem; In case of abnormal exhaust temperature, it is necessary to distinguish between single cylinder and full cylinder. In case of single cylinder abnormality, whether the instrument display is abnormal shall be considered, which can be eliminated by measuring thermoelectric EMF or conducting wire inversion. If this is a global anomaly, consider whether there is a change in gas concentration or poor ignition.

　　在故障排除時，當沒有有效的方法找出故障原因時，可以使用替代法。有疑問時點火控制器故障,例如,調整檢驗和特殊點火控制器連接到PC或筆記本電腦程序員來調整,但基本上不能配置這些測試設備維護單元,然后你可以把其他備用設備上的點火控制器拆開機運行后,通過觀察是否類似的故障再次發生,確定點火控制器是否損壞。

　　In troubleshooting, when there is no effective way to find out the cause of the fault, alternative method can be used. When in doubt, the ignition controller fails, for example, adjustment inspection and special ignition controller are connected to PC or laptop programmer for adjustment, but these test equipment maintenance units can not be configured basically. Then you can remove the ignition controller on other standby equipment for operation, and determine whether the ignition controller is damaged by observing whether similar failures occur again.

　　以上是燃?xì)獍l(fā)電機組廠家小編為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.pp198.cn

　　The above is the relevant content introduced by the small edition of gas generator manufacturers. If you want to know more, please visit the website: http://www.pp198.cn